Composite flooring is a material that has been used more and more in decoration and decoration in recent years. Because of its variety of colors and moderate prices, it is easy to maintain and is favored by many consumers.
The composite floor is not made of natural wood. Instead, the wood is crushed and then chemical preparations are added to the sheet to form a sheet. Then, wood grain paper is applied to the floor, and a wear-resistant layer is applied. The groove is then processed to form a groove. A composite floor with a beautiful texture. On the one hand, chemical agents such as glue used in the processing process have a certain impact on the human body. It cannot be said that he is environmentally friendly; on the other hand, he can use various types of wood trimmings for natural resources. The maximum utilization rate is very environmentally friendly. However, in the production process, manufacturers also pay attention to the use of more environmentally friendly chemical agents in order to achieve the smallest impact on the human body, so the composite floor can still be used with confidence.
The selection and purchase of laminate flooring is also a headache. Try not to choose products that are too cheap, at least for more than 50 yuan per square meter of the transaction price. As a non-professional consumer, it is better to choose a larger manufacturer and a better-known brand, whose quality is relatively guaranteed. In the selection of varieties, do not pick flowers, you can choose according to their preferences wood grain color.
The surface of the composite floor generally has crystal surfaces, relief surfaces and other varieties. Crystal surface is smooth, easy to clean, suitable for people like me lazy; embossed surface effect is good, but because of the surface roughness, dust easily fall into it, suitable for people who have the time to have the patience to clean. As for wear resistance, the individual feels that the bumps on the surface of the embossed surface seem to be more easily worn off, while the crystal surface is more wear-resistant because it is relatively flat.
Locking and non-locking are also a focus of choice. The clasp can close the two floors more closely and flatter. Personally think that it is better than non-locking. However, do not think that the choice of the lock can be as real as the dealer did not use glue, it is just eye-catching blind. In fact, the locking floor should still be glued, the glue can make the floor connection more secure, and the glue can prevent water from seeping into the floor seam to a certain extent. However, for those users who may be required to remove the floor and move it to another place in the near future, it is better to not use glue, so that the floor can be reused. The glue that the better floor manufacturer uses is to indicate that this manufacturer is exclusive, the quality is also better, the harm to the human body is relatively small. After a period of ventilation and volatilization, there is no problem.
Of course, there is a very important thing at the time of purchase. It is to ask the dealer for a product test report, such as a wear-resistant rotation report, an enclosed benzene volatilization test report, etc. Trying to buy a good product and satisfying itself rest assured.
I believe that the installation of laminate flooring is a stranger to everyone. After the floor arrives at home (usually some allowance will be put, and the actual amount of money will be used to pay back more and less money), the installed master will come to the door. The master first checked the condition of the ground and knocked over the ledge with a hammer, especially where the cement was not troweled after embedding. But don't expect him to do ground treatment for you. This is not his job. Then the master saw a small saw with a small electric saw, leaving the thickness of the laminate floor. Then began to lay the mats and bedding treasures, very simple, these two things are very easy to cut open, put them flat on the ground, the extra part of the edge with a utility knife to cut off on it.
Next to the floor, the first board must be in a corner of the room. The second board must not be a full board. The entire board must be sawn and the terminals of the two parallel boards must be opened. There are also several small pieces to be prepared as a reference for the seam between the floor and the wall. The left seam is to leave space for the floor to heat up and contract. It is generally about 1cm. My home is based on a small piece of 8mm thick laminate flooring. The seam is 8mm, but just after the Chinese New Year, it is over 40 degrees. In the summer's test, there was no problem with arching. It was very good. Not only the seam between the floor and the wall is to be left, but also the floor and the cabinet should be directly seamed, and the room door should be left in place. The paving of the entire room starts from one side of the room and gradually approaches the other side. First glue the glue in the groove of the board side (usually cut the tip of the glue bottle obliquely to facilitate the squeegee), then align the other board with the slot and install it. Then use a special box against the outer side and tap the box with a gimmick to keep the boards close together. Later they are good neighbors! The ground in the middle of the room is best paved. It is the most difficult on the side and on the corner. To measure the size, cut the board carefully, insert it carefully, and use a big iron-like ruler to hold the side. Then knock again. When you come across the corner and the door, it's even more troublesome. There is a waste, good masters do not have to worry about, will calculate well, try to help save.
After the board is fully laid out, it will be on the baseboard. Use a percussive drill to drill a row of holes on the floor near the floor in the strong lower part, knock in wooden pegs, install the skirting board, and fix it with a nail. Reminder: Be sure to mark the empty location in advance! The more common baseboards are two kinds of density plates and macromolecules. The density plates are more afraid of water and cannot be affected by blisters. At present, the more popular polymer baseboard, compared with the traditional MDF baseboard, has advantages such as color.
Floor acceptance room door price cement space decoration embossed cabinet door
Heavy Duty Caster-Top Plate Double Brake Type
Caster,Wheel Caster,Heavy Duty Caster
10 SERIES Light Duty Castors 40 SERIES HEAVY DUTY CASTER Co.,Ltd , http://www.chsteelcaster.com