Please call #332 Address: No. 146-148, No.7, Kangning Road, Hexi Industrial Park, Shushan District, Chongqing (professional sales of Chongqing feeder, punch feeder, three-in-one feeder, two-in-one automatic feeding straightening machine, material frame , leveling machine, metal slitting machine, Kaiping line and other equipment) 20 years of Taiwanese technology, national high-tech enterprises
The operation steps of the three-in-one feeder are briefly described as follows:
1. Feeding 1. Make sure all circuits, oil lines and gas lines are connected and there is no problem. Turn on the power and put the operation mode into manual mode. 2. Press the “retract frame†button to minimize the receipt of the rack; Open the pressure arm pressure switch and point the arrow to "A". At this time, press the arm to release it. 4. Press the "Trolley Back" button to return the trolley to the last end. 5. Place the roll vertically. On the trolley, then press the “Trolley Rise†or “Trolley Down†button to make the center of the coil as close as possible to the center of the rack; 6. After adjusting the center of the coil, press the “Trolley Forward†button to let The rack passes through the inner ring of the coil, and the center line of the material is coincident with the center line of the straightening machine as much as possible; 7. At this time, press the "rack expansion" button to make the rack tighten the inner ring of the coil; 8. Point the arrow of the press arm switch to “Bâ€, and let the presser wheel of the press arm press the outer ring of the coil; 9. After confirming that there is no problem, return the trolley to the last end and the loading is completed. 2. Feeding 1. Open the air control valve of the feeding device, let the supporting device lift up the supporting material, then open the air control valve of the pressing device to lift the pressing roller; 2. Relax into the discharge cylinder; 3. Pull One end of the coil is placed between the upper and lower rollers of the leveling machine; 4. Put the operation mode switch on the electric control box into the manual mode; 5. Click the “leveling forward†button until the material is completely extended. Up to the plane; 6. Adjust the stopper wheels on both sides to lock and feed. Note: The above operations must be performed in manual mode. The buttons used above in the automatic mode are invalid. Third, adjustment 1, adjust the correction effect, you can take a length of about 1.5 meters of uncorrected materials for debugging; 2, the correction effect is one of the important indicators of the correcting machine, the corrective machine has simplified the correction adjustment process, thus reflecting this Machine design with high efficiency and low labor intensity; 3. When adjusting the leveling roller, it should be noted that the left and right adjustment handwheel should be adjusted synchronously, and can be adjusted with reference to the ruler; 4. After the material to be processed is corrected to the requirements, it can be fed into the coil. Automate production. 4. Feeding 1, start the correcting machine or material frame, and slowly release the material; 2. Jog the flattening wheel to raise or flatten the wheel down button, adjust the gap between the upper and lower wheels, and finally use manual to adjust the fine adjustment; The function of the pressure spring is to apply pressure to the upper roller, so that the upper roller can press the material and send the material out, so the pressure should be based on the principle that the material does not slip, and the pressure should be greater when the thickness is thick; 4. Set the feeding After the length, look at the actual situation, set the corresponding feeding speed, the relevant setting method will be described in detail later; 5. When the relevant parameters of the feeding are set, the actual feeding length and setting are due to the number of the divisor. The value is not the same, so in the manual mode, press the feed test, punch, stroke, stamping, adjust the actual length of the feed; 6, when the tip of the guide pin in the mold enters the guide pin hole, you can adjust the loose screw to Come into the bearing of the relaxation bracket until the material is relaxed, and lock the screw nut (the pneumatically relaxed feeder should adjust the angle of relaxation, that is, about ±15° at the bottom); 7. Feeding open The adjustment is adjusted by the rotating cam of the punching machine. The so-called feeding start signal is to start feeding at the angle of the punching crankshaft. The recommended angle of the feeding angle of the machine is 9 to 3 (240°-90°); After the setting is completed, the test mode should be single-punched, and the production can be continued after adjustment.
Chongqing three-in-one feeder, Chongqing feeder--Jinyu machinery factory direct sales, really from Taiwan's 22-year-old feeder brand, Guangdong famous brand products, Guangdong Province enjoy government subsidized products, Jinyu Machinery / Jinlong Machinery Professional development, for each customer to customize the products to meet their own requirements, is the constant pursuit of Jin Hao people, welcome to inquire and negotiate. Http://news.chinawj.com.cn
Editor: (Hardware Business Network Information Center) http://news.chinawj.com.cn
Thin Brass Padlock low prices, high quality, loved by people around the world.
Suitable suitcase, drawer, door locks and other places does not store valuables.
Material: Brass Lock body, cylinder, chrome plated shackle
Purpose: lock boxes, cabinets, doors, etc.
Features lock all-copper, shackle sturdy rustproof
Thin Type Brass Padlock,Thin Brass Lock,Gate Brass Padlock,Single Skin Brass Padlock
Shengping Safety Protection Locks Manufacturer , https://www.chinajiuzhou.com