Renovation is indeed an annoyance for many people. For the lack of complete knowledge of decoration is reflected in the entire renovation of the entire process, but the completion of the inspection of the home inspection is a big problem, home improvement acceptance criteria need to pay attention to what knowledge? The next Xiaobian for everyone to introduce home improvement acceptance standards and home improvement acceptance considerations.
Home installation acceptance standards I. Acceptance standards for installation of water supply and drainage pipelines
The quality of pipelines and fittings should comply with the current standards; the installation of valves should be upright, and the switches should be flexible; with water pressure testing, all pipelines, valves, and joints should be free of water seepage and water leakage.
Home installation acceptance standards II, electrical engineering acceptance standards
The leakage switch is correctly installed and used normally; the installation and fixing of electrical devices and equipment should be firm and smooth; the electrical power test, lighting test and lamp control performance are good; the appearance of switches, sockets, terminal boxes and other devices are intact, and the insulation device is crack-free. Firm, flat, and installation methods are in compliance with the regulations; deviations of switches and socket terminal boxes installed side by side; clearances of concealed switches, sockets, terminal boxes, and the perimeter of the box are in compliance with the regulations; weak electrical systems are fully functional and meet the requirements for use. Appliances are firmly installed. , flat.
Home improvement acceptance standards III. Paste acceptance criteria
After the paper is finished and dried, it can be accepted; when it is accepted, check whether the material type, color and pattern meet the design requirements; the wallpaper and wall cloth must be firmly bonded and the surface color is the same, and there must be no bubbles, empty drums, cracks, and creases. And stains, no squinting glue marks; surface smooth, no corrugations, wallpaper, wall cloth and hanging mirror line, top corner line, paste the face plate, skirting board, lining board layering, curtain hanging box next to, distance 1.5 meters At the office, there must be no obvious gaps in the visual inspection; the stitching is horizontal and vertical, and the pattern and pattern of the stitching are consistent, not separated from each other, and not overlapped; the yin and yang corners are vertical, the edges and corners are clear, the shadows at the inside of the corner are smooth, and there is no seam at the outside corners. The edges of wallpapers and wall coverings are straight and tidy, and there must be no paper hair or splinters; there must be no leakage, subsidies, and delamination.
Home improvement acceptance standards IV. Acceptance standards for decorative works
After the floral decoration project is completed and dried, it can be checked; if the floral decoration project is accepted, it should check whether the varieties, specifications and patterns of the floral ornaments meet the design requirements; the floral ornaments should be installed firmly, and their quality requirements and allowable deviations should be in accordance with: the level of the striped floral ornaments and Permissible vertical deviation, the total length of not more than 3 mm; allowable deviation of the position of the individual floral ornaments, shall not be greater than 10 mm; floral ornament surface should be smooth, clear pattern, tight seams, no cracks, warping, lack of edges and other defects; The surface of the flower should be clean and clear with no cracks.
Home Acceptance Criteria V. Ceiling Project Acceptance Criteria
The variety, specification, color of the materials used in the ceiling project shall conform to the requirements of the design specifications; the cover panel and the keel shall be tightly connected, the surface shall be smooth, and shall not be contaminated, fractured, missing corners, hammers, etc. Defects, joints should be uniform, paste the cover panel must not be delaminated, plywood shall not be through the place; Shelving cover panel shall not have leakage, penetration, angle phenomenon.
Home installation acceptance standards VI. Acceptance standards for installation of wooden floors
Materials should meet the household's requirements and current product standards; flooring installation (bonding) should be solid, no sound, no loosening; wooden floor surface should be polished, no planing, shavings and burrs, varnish flooring The pattern (wood grain) should be clear; the parquet floor seams should be aligned, the gap width is uniform, the surface is clean and there is no glue overflow phenomenon; the skirting board is closely connected with the floor; the skirting board is straight and the full length height difference should be no more than ±3 mm. The wall is tight and seamless.
Acceptance criteria for home improvement VII. Acceptance standards for construction quality of plastic board surface
Materials, color, and paving should meet the requirements of the households; the surface should be smooth, smooth, wrinkle-free, and free of edging and bubbling; uniform color, tight joints, and straight edges on all sides; degumming should not be more than 20 mm, and the distance between them should not be less than 500 Millimeters; should be tight, firm and flat with the pipe joints; the skirting board should be closely connected with the plastic plate; the skirting board should be straight and the full length height difference should not exceed ±3 mm, which should be close to the wall surface without any gap.
Home installation acceptance standards VIII. Acceptance standards for construction quality of plate surface
Material and pattern meet the requirements of the households, product quality in line with national standards and technical regulations; paving should be solid, not loose, the level of the ground level is not greater than 0.5 mm; paving pattern is clear, no stain, pulp marks; seam straight, pull through Seam inspection, the deviation is not more than 2 mm; the seam width is not more than 1.0 mm; the height difference between the block and the block is not more than 0.5 mm.
Home installation acceptance notice
1. The quality of the pipes and fittings installed in the house must meet the current standards. The installation of the valve must be correct and the switch must be flexible. During the water pressure test, whether there is water seepage or water leakage in pipes, valves and joints.
2. Be sure to check whether the switch of the electrical appliance and the terminal box of the socket are leaky. Check if the device and equipment of the electrical appliance are firmly mounted and flat. Whether the power of the electric appliance is normal or not, and whether the lighting switch has good control performance.
3, the acceptance of the paste, we must carefully check the use of materials in the decoration of the varieties, colors, patterns, etc. meet the design requirements. Wallpapers and wall coverings should be firmly bonded, and the gloss on the surface must be consistent. There must be no phenomena such as air bubbles, empty drums, and cracks. In addition, the stitching must be horizontal and vertical, and the pattern and pattern of the stitching must be consistent and there must be no separation.
4. The types of materials, specifications, colors, basic structure and fixing methods used in the ceiling project must meet the requirements of the relevant design specifications. The connection between the cover panel and the keel must be tight and the surface must be flat. There are defects such as contamination, missing corners, and joints. The joints must be uniform.
5. When the owner tests the presence of empty drums in the wall tiles and floor tiles, he can use a small metal hammer and tap it gently against the wall tiles and floor tiles to hear if there is an empty sound, and the floor tiles and the wall tiles are empty. The drum rate should not exceed 5% of the total paving area, otherwise shedding will easily occur.
Editor's summary: On the acceptance criteria of home improvement and home improvement acceptance notice are introduced here, I hope to be helpful to everyone. If you want to know more about yourself, you can follow the information on this site.
Home improvement and home improvement acceptance standards
Solar Mounting Brackets are made of hot galvanized steel Q235 and used for solar pannel in concrete base,roof,ramming pole,carport,green house and etc.They have the advantages of easy instalation, steady and safety,excellent duration and great flexibility. High pre-assembly parts and customized solution to save your install time and money.
Installation:
1.Ships in a few small boxes reducing material costs and simplifying shipping and handling.
2.No rails means mounts-to-modules instead of mounts-to-rails-to-modules, making installation fast and simple.
3.Works with standard modules. Simply drop in the modules, tighten down the clamps, and you're done.
Features & Benefits:
1.Works with standard module frames - providing greater flexibility
2.Engineered to be structurally robust & simple, with minimal leveling
3.Easy to handle and transport - ships in small boxes
4.Cost savings with integrated grounding, requiring less copper and grounding hardware
5.Elegant, sleek design means more referrals from
happy homeowners
6.Quick Rack comes with easy-to-use design software
Solar Mounting System,Advanced Solar Mounting System,Ground Screws for Solar Mounting,Solar Mounting Structure
Hebei Honde Plastic & Metal Co., Ltd. , https://www.foundation-system.com