After a certain amount of time, the wooden doors naturally become old, which is unavoidable. However, if you want to change a door again, the cost will definitely be relatively high. You may wish to refurbish it at this time. I believe there will be unexpected surprises. How can the old door with a door frame be renovated better? The following Xiao Bian took everyone to learn the next two methods of renovation of the old door.
How to refurbish the old door with a door frame A old wooden door refurbishment sticker
Protecting the surface of old wooden doors is one of the methods for refurbishing old wooden doors. Stickers have always occupied a place for refurbishing wooden doors with their environmentally friendly, convenient, and quick construction methods. When you post wallpapers, you must select the materials and types of wallpapers, and choose high-quality wooden door stickers from the perspective of safety and environmental protection. The specific method is as follows:
1. Remove the door and place it in a basic level. Then lay the paper to be tiled on the door and align the corners. Set a weight in the middle to prevent the paper from shifting. Then spread some heavy objects, mainly to smooth the paper.
2. The length and width of the paper should be calculated as the thickness of the door for wrapping. When opening the sticker, remove the release layer from one corner. This corner must be tightened, and stick the inside of the anti-sticking layer. After sticking the corners, pull the anti-adhesive layer in one direction and open the direction as far as possible. The direction of the corner is torn apart, which is mainly to fix the right side. You can tear it and press it with your hands. When you encounter heavy loads, remove it. It's better to have two people and the effect will be better.
3. When the right side is fixed, it is necessary to pull the anti-sticking layer to balance with the left side, and then remove all the weights. When pressing, the center line is the main direction, and the right side is pushed horizontally. After the flattening, the excess sticker was cut with a knife, and the old wood door renovation sticker was completed.
How to refurbish the old door with a door frame II. Paint the paint to renovate the wooden door
The wooden door was used for a long time, and the surface began to blacken and roughen. The easiest way to renovate a wooden door is to repaint it and paint it to achieve the desired effect. It should be noted here that it is better to remove the door and put it in a special room for spraying. Once there was no dust, environmental pollution was reduced; secondly, the front and back of the door could be seen clearly. If sprayed directly on the door, it is prone to mist when sprayed, affecting the sight and spraying effect, and the inhalation of these mists can cause damage to the respiratory system. The specific method is as follows:
1. Remove the handles and other accessories on the wooden door so as to prevent the next step from scratching the hand and also help the paint evenly.
2. Use coarse sandpaper to polish the places where you need to paint. If the surface is seriously damaged, you should try to polish the old paint film, especially the loose paint film. As far as the degree of grinding is concerned, it is only necessary to be tight and smooth. Note that the corner should not be polished too much and keep the original shape of the wooden door. Use a cloth dampened with water to create a semi-wet condition and clean the powder on the recently polished wooden door. Take fine sandpaper and polish it again, paying attention to the corners. Use a damp cloth to clean the powder. This step is very important, so that the paint on the wooden door is stronger.
3. Take paint, brush, paint cover. Dip the brush in the paint bucket. Do not touch too much paint at one time. The rules for painting are from top to bottom and from left to right. Pay attention to the corners and concealed areas.
4. Put the wooden door that has been painted over for four to five hours until the paint dries out. After the paint is dry, take the fine sandpaper and polish it again from beginning to end. This time, the sanding is done to smooth the unevenness of the brush on the paint, which helps to continue the painting. Apply the second pass of paint as above. If the paint is too thick, add appropriate amount of rubber water, dilute the paint and brush again. Then continue to dry and polish.
5. After the third pass of painting according to the above method, the wooden door paint is brushed. Finally, install door handles, hinges, and other hardware and accessories. In this way, the entire wooden door was painted. At this time, you will find that the paint on the wooden door is even and beautiful, and the whole room is beautiful.
The article concludes: The above is about how to renovate the old door with a door frame. The two major methods are introduced. I believe that after everyone read the Xiaobian's share, they have learned about the renovation of the wooden door. In fact, the renovation of the old door is not a simple matter, so I hope that the above methods and techniques will give you some help!
Plastic Sheathed Copper Tube,PVC Sheathed Copper Tube,Plastic Coasted Copper Tube,PVC Coasted Copper Tube,PE Sheathed Copper Tube,We can supply tube-with-wire type, coated by PVC Sheath, as per customers` choice. The tube-with-wire type is unique design with our patent specially for CNG/LPG transport, which can improve efficiency and reduce cost for installation of Auto CNG/LPG system.
Plastic Sheathed Copper Tube
Plastic Sheathed Copper Tube,PE Sheathed Copper Tube,PVC Sheathed Copper Tube,PE Coasted Copper Tube,PVC Coasted Copper Tube
Taizhou Runde Company , https://www.smartfittings.com